Products

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Braktec brake system

• Universally applicable for mounting the GPS bracket

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Prevents the hand grips from chafing in the event of a fall

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

Provides optimum protection

Already mandatory in many competitions

Visual highlight

Larger than stock handlebar pad

These CNC-machined, high-strength aluminum handlebar risers are extremely robust thanks to their special screw fastening (from below) on the triple clamp

Twisting and bending are therefore practically impossible

Use of these handlebar risers is only possible on CNC-machined triple clamps

Available in three different heights

• CNC milled from high-strength aluminium
• Improves heat dissipation
• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components

• CNC milled from high-strength aluminium
• Resistant to the toughest stresses and strains
• Uncompromising race look

• Know exactly when the next service is due

• Exceptionally robust
• Extremely light

Left hand side fairing

Left hand side fairing

• Tool for lifting the motorcycle
• Stroke: 315/425 mm
• Maximum load: 150kg

• Right grip permanently glued to the throttle grip
• Left grip with aluminium clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

Lower section of the air box

Lower section of the air filter

With scaling for both the fluid level and different mixture ratios

Perfect for changing the oil and for preparing larger quantities of 2-stroke mixture in the canister

Simple handling thanks to the ergonomic design

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

• Plug-in stand and fork support in one part
• Two tools in one
• Saves space when transporting your motorcycle
• Stabilizes the motorcycle during transport
• Protects the fork shaft sealing rings and fork springs against damage due to tension belts being tightened too much
• After transport, the tool serves as a perfect plug-in stand!

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Includes drilling for safety wire

• CNC milled from high-strength aluminium
• Elegant anodized surface
• Visual highlight

• CNC milled from high-strength aluminium
• Elegant anodized surface
• Visual highlight
• Includes drilling for safety wire

PHDS bracket for factory steering damper

Original fairing parts, without the standard decor

Optimal basis for creating a unique design

Perfect fit

Personalise the look of your motorcycle

Kit contains:

Fender

Air filter cover

Air filter panel

Side fairing

Spoiler set

Start number plate

Headlight shroud

Tail section

Fork protector

Original fairing parts, without the standard decor

Optimal basis for creating a unique design

Perfect fit

Personalise the look of your motorcycle

Kit contains:

Fender

Air filter cover

Air filter panel

Side fairing

Spoiler set

Start number plate

Headlight shroud

Tail section

Fork protector

Keeps water out of the silencer during cleaning

For inner-diameter of 22-42 mm

• Stabilizes the motorcycle during transport
• After transport, the tool serves as a perfect plug-in stand!

Very easy operation

Extremely low weight

Fast preload adjustment

Use of the entire length of the thread on the shock absorber

Dirt-resistance

Mechanical drive

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

Upgrade your bike with this factory handlebar and make use of the advantages of an adjustable crossbar, depending on the track ground:

When locked, the crossbar is solid (stiff)

When unlocked, the crossbar is flexible

Dimensions: A = 112 mm, B = 811 mm, C = 88 mm

• For all 48 mm forks
• Extra strong film

• For all 48 mm forks
• Extra strong film

• Guaranteed perfect protection in all seasons
• Made of exclusive, pigmented fabric
• Includes practical carrying bag
• Protects the motorcycle from dust, scratches and the like

• Provides better cooling of the engine
• Provides more air
• Maximum performance
• Digital control
• Current temperature can be read at any time
• Variable switch-on temperature between 65 °C and 95 °C
• Switch-off temperature 1 °C below the selected switch-on temperature