Products

Protects the intake system against water and dirt when cleaning the air filter box

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

• Highest quality workmanship
• Including straps

Developed together with the vehicle

Specially developed for WP forks

Fork bleeding using finger pressure

Perfect for all on the move

Exceptionally robust

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

CNC milled from high-strength aluminium

Elegant anodized surface

Visual highlight

Increased performance

Designed to get the best performance from the motorcycle

Twice as many reed petals compared to stock for maximum performance

Extremely robust spark plug

Centre electrode tip made of iridium

Reinforced ground electrode

Special design for better ignition and performance

Copper gasket for improved heat dissipation

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Optimally tuned steering stem stiffness

100% alignment of the fork tubes

Ideal flexibility – precisely customised to the WP fork

Specially optimised geometry of the fork clamping

No ovalization of the fork outer tube

Highly precise and smooth fork response

Maximum handling gain

Gain in stability at the front wheel

Overall, more homogeneous force flows in the entire vehicle

Including steering stem with steering head bearing already pressed on

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

100 mm length

20 blades: 0,05 - 0,1 - 0,15 - 0,2 - 0,25 - 0,3- 0,35 - 0,4 - 0,45 - 0,5 - 0,55 - 0,6 - 0,65 - 0,7 - 0,75 - 0,8 - 0,85 - 0,9 - 0,95 - 1,0 mm

• Contents are in accordance with DIN standard 13167-2014 for motorcyclists
• Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain)

Full sound

Extra strong sheet steel

Nickel-plated surface

Better power delivery

Higher maximum power

Combination with FMF silencer recommended

Specially developed for use in motocross

Silencer housing made of high-grade aluminium

Stainless steel silencer cap

Rich sound

Permanently welded brackets

Easy to mount

Reduced weight

For a system with optimized performance and perfect balance we recommend the combination with the FMF Fatty expansion chamber

Small and light, so very portable - saves the day in the event of a puncture on the move!

Mini-foot pump with pressure gauge on the swivelling valve head that fits all prevalent valves

Integrated double-cylinder with pressure switch-over to high pressure

Maximum 12 bar

Height: approx. 170 mm folded together

• Convenient and easy to use
• Very easy operation
• Adjusting the air pressure

• Convenient and easy to use
• Very easy operation

Protects the frame without changing the slim lines of your motorcycle

• Coated neoprene ring
• Simply pulled over the grips
• Optimum protection against blisters on the thumbs with these coated neoprene rings

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

These CNC-machined, high-strength aluminum handlebar risers are extremely robust thanks to their special screw fastening (from below) on the triple clamp

Twisting and bending are therefore practically impossible

Use of these handlebar risers is only possible on CNC-machined triple clamps

Available in three different heights

CNC milled from high-strength aluminium

Resistant to the toughest stresses and strains

Weight-optimised

• Know exactly when the next service is due

Perfect fit

Elegant anodised surface

Combined with FMF pipe and silencer it offers an increased power delivery especially in high rpms

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

Secure stand for your bike

Made especially for 50 / 65 / 85 models

Aluminium construction with a non-slip pad.

The top is wedge shaped and solid so the bike doesn't slide around when washing.

With scaling for both the fluid level and different mixture ratios

Perfect for changing the oil and for preparing larger quantities of 2-stroke mixture in the canister

Simple handling thanks to the ergonomic design

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

• CNC milled from high-strength aluminium
• Elegant anodized surface
• Visual highlight
• Includes drilling for safety wire

Keeps water out of the silencer during cleaning

For inner-diameter of 22-42 mm

• Stabilizes the motorcycle during transport
• After transport, the tool serves as a perfect plug-in stand

Increased safety for the racers of the future

A more intermediate power kit unleashing 8 hp

Increased safety for the racers of the future

Reduces the power to moderate and controllable 4 hp

Very easy operation

Extremely low weight

Fast preload adjustment

Use of the entire length of the thread on the shock absorber

Dirt-resistance

Mechanical drive