Products

Protects the intake system against water and dirt when cleaning the air filter box

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

• Highest quality workmanship
• Including straps

Developed together with the vehicle

Specially developed for WP forks

Fork bleeding using finger pressure

Perfect for all on the move

Exceptionally robust

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Higher speed

Optimised ignition timing

Increased performance

Designed to get the best performance from the motorcycle

2 different ignition curves are available

The first curve brings more power in the higher rev range

The second curve (plugged off) brings also more power compared to the stock CDI control unit but is reducing detonation

Therefore for sand recommended

How to switch between the ignition curves have a look at the bike manual

Maximum performance can be reached together with our FMF exhaust system

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

CNC milled from high-strength aluminium

Elegant anodized surface

Visual highlight

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Increased performance

Designed to get the best performance from the motorcycle

Twice as many reed petals compared to stock for maximum performance

Custom designed seat for an uncompromising look

Resistant coating

Seat cover with transversely stitched ribs

Maximum grip with unrestricted freedom of movement

Same seat height like the standard seat

Extremely robust spark plug

Centre electrode tip made of iridium

Reinforced ground electrode

Special design for better ignition and performance

Copper gasket for improved heat dissipation

• Made of high-strength aluminium
• Elegant anodized surface
• Pure race feeling
• Provides more traction when starting
• Mounted directly on the fork

Elegant anodised surface

Visual highlight

CNC milled aluminium triple clamp

Optimally tuned steering stem stiffness

100% alignment of the fork tubes

Ideal flexibility – precisely customised to the WP fork

Specially optimised geometry of the fork clamping

No ovalization of the fork outer tube

Highly precise and smooth fork response

Maximum handling gain

Gain in stability at the front wheel

Overall, more homogeneous force flows in the entire vehicle

Including steering stem with steering head bearing already pressed on

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

100 mm length

20 blades: 0,05 - 0,1 - 0,15 - 0,2 - 0,25 - 0,3- 0,35 - 0,4 - 0,45 - 0,5 - 0,55 - 0,6 - 0,65 - 0,7 - 0,75 - 0,8 - 0,85 - 0,9 - 0,95 - 1,0 mm

• Contents are in accordance with DIN standard 13167-2014 for motorcyclists
• Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain)

Full sound

Extra strong sheet steel

Nickel-plated surface

Better power delivery

Silencer housing made of high-grade aluminium

Stainless steel silencer cap

Rich sound

Permanently welded brackets

Easy to mount

Reduced weight

For a system with optimized performance and perfect balance we recommend the combination with the FMF Fatty expansion chamber

Small and light, so very portable - saves the day in the event of a puncture on the move!

Mini-foot pump with pressure gauge on the swivelling valve head that fits all prevalent valves

Integrated double-cylinder with pressure switch-over to high pressure

Maximum 12 bar

Height: approx. 170 mm folded together

• Convenient and easy to use
• Very easy operation
• Adjusting the air pressure

• Convenient and easy to use
• Very easy operation

• Coated neoprene ring
• Simply pulled over the grips
• Optimum protection against blisters on the thumbs with these coated neoprene rings

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting.

Lightweight material

Open design

Fastening directly on the handlebar or with a special support directly on the fittings

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Colored top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

These CNC-machined, high-strength aluminum handlebar risers are extremely robust thanks to their special screw fastening (from below) on the triple clamp

Twisting and bending are therefore practically impossible

Use of these handlebar risers is only possible on CNC-machined triple clamps

Available in three different heights

Perfect fit

Resistant coating

Higher compared to the standard seat

CNC milled from high-strength aluminium

Resistant to the toughest stresses and strains

Weight-optimised

• Know exactly when the next service is due

• Ignition curve adjustment made easy!
• Comfortable ignition curve adjustment on the handlebar