EC250 2021

Air filter box front part

Air filter box front section

• Protects the intake system against water and dirt when cleaning the air filter box

Perfect fit

Optimal basis for graphics kits

Perfect fit

Optimal basis for graphics kits

• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover

• Recommended for extremely dusty conditions

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

• Highest quality workmanship
• Including straps

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Height: 43 cm

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Height: 43 cm

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tire changes, brake service etc. without removing the brake cover

Manufactured using state-of-the-art 2-component injection moulding technology

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

Perfect for all on the move

Exceptionally robust

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

• Visual highlight
• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

Chain breaker

Patented gage for two important checks:

Check and adjust chain tension

Check chain lengthening (wear)

• Easy to mount
• Protects from damage in the event of a fall

• Easy to mount
• Protects from damage in the event of a fall

• 80 % lighter than steel with the same load-bearing capacity
• Elegant look
• Low thermal expansion
• Made of high-quality carbon
• High long-term temperature stability
• Non-corrosive
• Maximum protection against falls, flying stones, branches, etc.
• Can only be fitted with a standard header
• High stiffness and strength

Race look

Visual highlight

With exchangeable chain track surface, therefore extremely durable

Specially designed for the challenges of off-road use

• Anodized hub milled from a whole piece
• Maximum weight saving compared to standard wheels
• Maximum gain in handling and, at the same time, stability in challenging off-road situations
• Anodized aluminum spoke nipples

CNC milled from high-strength aluminium

Elegant anodized surface

Visual highlight

• Made of the highest quality materials
• Visual highlight
• Perfect fit
• Personalize the look of your motorcycle
• Race look
• Designed to completely change the original look of your motorcycle
• Glue the graphics kit directly onto the standard fairing parts
• Can be removed without leaving any residue

Manufactured using state-of-the-art 2-component injection moulding technology

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tyre changes, brake service etc. without removing the brake cover

Noble material mix of carbon fibre and plastic

Up to 260mm brake disc

Race look

Visual highlight

With exchangeable chain track surface, therefore extremely durable

Specially designed for the challenges of off-road use

CNC machined out of teflon