EC250 2023

• Reduces dirt deposits between engine and skid plate
• Provides better cooling of the engine

• Easy to mount
• Protects from damage in the event of a fall

• Easy to mount
• Protects from damage in the event of a fall

• Prevents abrasion of the frame by dirt, falls or the driver's boots
• Protects trousers and boots from burns on the exhaust side

For all 48 mm forks

Ideal protection for sealing the fork

For use with an open fork protector

• Anodized hub milled from a whole piece
• Maximum weight saving compared to standard wheels
• Maximum gain in handling and, at the same time, stability in challenging off-road situations
• Anodized aluminum spoke nipples

• 5 x 17"
• Black matte
• Comes with bushings for 20mm axle diameter
• Can be adapted to other axle diameter by using the bike's stock bushings

• 3.5 x 16.5"
• Black matte
• Comes with bushings for 26mm axle diameter
• Can be adapted to other axle diameter by using the bike's stock bushings

• Universally applicable for mounting the GPS bracket

• CNC milled from high-strength aluminium
• Improves heat dissipation
• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components

• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover

• Recommended for extremely dusty conditions

• Developed according to the requirements of our factory drivers
• Gain in stability at the front wheel
• High-end steering damper
• Maximum control on fast tracks
• Fully adjustable
• Well thought-out mounting of the damper enables individual handlebar adjustment
• Reduced weight
• Sensitive response behavior
• High speed DCC
• Optimum 25 click setting range.
• Proven success with the KTM Works Rally Team.

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent (A54007930000FA) is required

Steering damper bracket

Steering damper counter bearing

PHDS bracket for factory steering damper

Factory steering damper bracket

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodized against corrosion
• The interior, made of a special alloy, is also hard anodized to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad
• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

Upgrade your bike with this factory handlebar and make use of the advantages of an adjustable crossbar, depending on the track ground:

When locked, the crossbar is solid (stiff)

When unlocked, the crossbar is flexible

Dimensions: A = 112 mm, B = 811 mm, C = 88 mm

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Including all required assembly materials
• Extremely sturdy aluminium brackets
• Prevents broken levers

• Made of sturdy plastic
• Converts the originally open handguards into a closed version
• Mounting independent to the lever mounting, directly to the handlebar
• Compatible also with handguards 79602979000EB/28/30/AB and 72102979000EB/28/30

• To make the mounting of the wrap-around handguard kit 79702984044 resp. of the Handguard kits 7970297900030 / 28 / AB / EB easier
• Increases the space between alu-guard and hand brake cylinder

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Warm hands, no matter what the weather

• A motorcycle hand grip can be mounted on the handle (not included)

• Right grip permanently glued to the throttle grip
• Left grip with aluminium clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary