EC250F 2021

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

• Highest quality workmanship
• Including straps

• Developed together with the vehicle
• Specially developed for WP forks
• Fork bleeding using finger pressure

Perfect for all on the move

Exceptionally robust

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

CNC milled from high-strength aluminium

Elegant anodized surface

Visual highlight

• 100 mm length
• 20 blades: 0,05 - 0,1 - 0,15 - 0,2 - 0,25 - 0,3- 0,35 - 0,4 - 0,45 - 0,5 - 0,55 - 0,6 - 0,65 - 0,7 - 0,75 - 0,8 - 0,85 - 0,9 - 0,95 - 1,0 mm

• Contents are in accordance with DIN standard 13167-2014 for motorcyclists
• Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain)

Small and light, so very portable - saves the day in the event of a puncture on the move!

Mini-foot pump with pressure gauge on the swivelling valve head that fits all prevalent valves

Integrated double-cylinder with pressure switch-over to high pressure

Maximum 12 bar

Height: approx. 170 mm folded together

• Coated neoprene ring
• Simply pulled over the grips
• Optimum protection against blisters on the thumbs with these coated neoprene rings

These CNC-machined, high-strength aluminum handlebar risers are extremely robust thanks to their special screw fastening (from below) on the triple clamp

Twisting and bending are therefore practically impossible

Use of these handlebar risers is only possible on CNC-machined triple clamps

Available in three different heights

• Know exactly when the next service is due

With scaling for both the fluid level and different mixture ratios

Perfect for changing the oil and for preparing larger quantities of 2-stroke mixture in the canister

Simple handling thanks to the ergonomic design

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

• CNC milled from high-strength aluminium
• Elegant anodized surface
• Visual highlight
• Includes drilling for safety wire

• Keeps water out of the silencer during cleaning
• For inner-diameter of 15-37mm

Keeps water out of the silencer during cleaning

For inner-diameter of 22-42 mm

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

The repair kit is a two-component epoxy resin adhesive. Hardens at room temperature: accelerated hardening possible by raising the temperature

Use: Particularly suitable for steel, but also other metals, wood, concrete, ceramics, glass and most plastics. The steel bond is resistant to, among other things, oil, gasoline, diesel and battery acid

Processing: Best results are achieved with clean and rough surfaces. Cut off the required amount and knead for approx. 1 minute until a uniform color is achieved. Use within 2 minutes

At first, it seems as if there is no adhesion. Just carry on and press the adhesive mixture into the surface. Remove any excess material. When coating or repairing surfaces that are still wet, leak or are under water, apply pressure until adhesion begins. Smooth flat with water by hand for an even surface. Wash your hands with soap and water (or with a Turbo cleaning towelette) immediately after completing your work. Hardening commences after 5 to 10 minutes

The repaired part can be used again after as little as 60 minutes. The surfaces to be glued must be dry and free from dust and grease

Contents: 56 g

Makes setting the sag significantly simpler

Folding version for easy stowing in the tool box

• Contains all the most-used bolts and small parts for current Offroad models
• 30 % saving compared with purchasing individual parts

Recommended for storing your timecard during races

Stick it directly to the seat with grip glue

• Already mandatory in many competitions
• Complies with FIM regulations
• Rubberized back

This mat is already mandatory for many races

Complies with FIM regulations

The special material mix absorbs overflowing fuel

The mat also facilitates the retrieval of tools, screws and other small parts during service work

Rubberised back

Size: 170 cm x 100 cm

• Convenient and easy to use
• Easy handling and operation
• Comfortable unhooking of springs

Made of robust material

Pre-cut stickers

Know exactly when the next service is due

Including rev counter

Medium strength thread lock - contents, 50 ml

• Temperature resistant from -55 to +200 °C
• Fills gaps up to 0.25 mm
• Final strength achieved after 1 to 3 hours

Enables secure fastening of the machine

Protects handlebar and tank from scratches

Made from durable ballistic nylon

Load capacity of 280 kg

With handlebar loops

With rubberized hooks and carabiner on belt ends

There's racing experience here as well!

Practical tire iron - long version for minimum effort

There's racing experience here as well!

Practical tire iron - short version ideal for the portable tool bag

There's racing experience here as well!

Practical tyre lever set, consisting of

3 x short version 51012092100

3 x long version 51012093100