EC250F 2023

• Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel
• Reduces wear on sealing rings and wheel bearings for longer service life

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

• Anodized hub milled from a whole piece
• Maximum weight saving compared to standard wheels
• Maximum gain in handling and, at the same time, stability in challenging off-road situations
• Anodized aluminum spoke nipples

• 5 x 17"
• Black matte
• Comes with bushings for 20mm axle diameter
• Can be adapted to other axle diameter by using the bike's stock bushings

• 3.5 x 16.5"
• Black matte
• Comes with bushings for 26mm axle diameter
• Can be adapted to other axle diameter by using the bike's stock bushings

• Universally applicable for mounting the GPS bracket

• Optimal solution for quick and secure fastening of your smartphone on the vehicle

• Protects your expensive smartphone from rain, dust or mud
• Touchscreen remains fully functional
• Optimal solution for quick and secure fastening of your smartphone on the vehicle

• CNC milled from high-strength aluminium
• Resistant to the toughest stresses and strains
• Uncompromising race look

• CNC milled from high-strength aluminium
• Improves heat dissipation
• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components

• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover

• Recommended for extremely dusty conditions

• Developed according to the requirements of our factory drivers
• Gain in stability at the front wheel
• High-end steering damper
• Maximum control on fast tracks
• Fully adjustable
• Well thought-out mounting of the damper enables individual handlebar adjustment
• Reduced weight
• Sensitive response behavior
• High speed DCC
• Optimum 25 click setting range.
• Proven success with the KTM Works Rally Team.

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent (A54007930000FA) is required

Steering damper bracket

Steering damper counter bearing

PHDS bracket for factory steering damper

Factory steering damper bracket

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

• Two handlebars in one
• The exterior ensures maximum resistance to external damage (e.g. fall)
• Additionally hard anodized against corrosion
• The interior, made of a special alloy, is also hard anodized to protect it from damage by the handlebar controls.
• Nylon inserts in the inner tube allow thinner walls
• Very good flex properties
• Comes with handlebar pad
• Dimensions: A = 118 mm, B = 811 mm, C = 74 mm

Upgrade your bike with this factory handlebar and make use of the advantages of an adjustable crossbar, depending on the track ground:

When locked, the crossbar is solid (stiff)

When unlocked, the crossbar is flexible

Dimensions: A = 112 mm, B = 811 mm, C = 88 mm

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

• Know exactly when the next service is due

LED technology, specially developed for use with the Enduro

Very high light output

Light intensity 1500 lm

Light colour approx. 5,500 K

Exceptionally robust

Comes with white headlight mask for plug & play mounting

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Including all required assembly materials
• Extremely sturdy aluminium brackets
• Prevents broken levers

Maximum protection against falls, flying stones, branches, etc

Indispensable companion for heavy off-road and Supermoto use

Wide, generous design in combination with sturdy aluminium bracket

Prevents broken levers

Made of robust plastic

• Made of sturdy plastic
• Converts the originally open handguards into a closed version
• Mounting independent to the lever mounting, directly to the handlebar
• Compatible also with handguards 79602979000EB/28/30/AB and 72102979000EB/28/30

• To make the mounting of the wrap-around handguard kit 79702984044 resp. of the Handguard kits 7970297900030 / 28 / AB / EB easier
• Increases the space between alu-guard and hand brake cylinder

Made of robust plastic

Fastening independent of fittings directly on the handlebars

To convert the open, standard handguards to a closed version