EC250F 2024

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Braktec brake system

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tire changes, brake service etc. without removing the brake cover

Manufactured using state-of-the-art 2-component injection moulding technology

• Teeth made of high-strength steel, for an extra long service life
• Aluminium centre section, reduces unsprung masses
• Permanently joined together with high-strength rivets
• At least three times longer service life than other aluminium rear sprockets
• 50 % lighter than steel rear sprockets
• Longer service life of the entire drivetrain kit

• Protects your expensive smartphone from rain, dust or mud
• Touchscreen remains fully functional
• Optimal solution for quick and secure fastening of your smartphone on the vehicle
• Handlebar pad and smartphone holder in one
• Smartphone cover with velcro fastener attached to the handlebar pad
• Smartphone can be easily removed with its cover
• For Smartphones up to 160 x 80 mm
• Comes with two separate protective strips in case the sleeve is not used
• Can also be fitted in combination with the PHDS-handlebar support
• Smartphone not included!

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

Higher compared to the standard seat

Resistant coating

+35mm

CNC milled from high-strength aluminium

Elegant anodized surface

Visual highlight

Protects the frame without changing the slim lines of your motorcycle

Manufactured using state-of-the-art 2-component injection moulding technology

Mounting directly on the frame

Prevents abrasion of the frame by dirt, falls or the driver's boots

Reliable protection of valuable motorcycle components

Better control due to better contact with your bike

Resistant coating

Enables shorter drivers to also achieve the optimum seat height

Lower compared to the standard seat

Resistant coating

Higher compared to the standard seat

+20mm

• Anodized valve caps
• With valve opener function

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Prevents the hand grips from chafing in the event of a fall

Resistant to the toughest stresses and strains

Forged lightening indents reduce rotational mass

Grooves between the teeth clear dirt under the chain

Extends chain life

• CNC milled from high-strength aluminium
• Elegant anodized surface
• Visual highlight
• Includes drilling for safety wire

CNC milled from high-strength aluminium

Elegant anodized surface

Visual highlight

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Fits all Braktec brake- and clutch reservoirs

This clever tool is a must for every motorcycle toolbox

With it, you can remove dirt from your fork seals effortlessly

No matter whether it's in the garage or directly at the racetrack this tool extends the life of your seals many times over

For all 48 mm forks

Stabilises the motorcycle during transport

Protects the fork shaft sealing rings and fork springs against damage due to tension belts being tightened too much

Is clamped between the bottom of the front fender and tyre

Permanent protection against unattractive scratches and matte spots on the swingarm

Protects from damage in the event of a fall

Prevents abrasion of the frame by dirt, falls or the driver's boots

Protects trousers and boots from burns on the exhaust side

Elegant look

Acts as an additional protective layer

Recommended for extremely dusty conditions

Premature sanding of the air filter is avoided

Coarse-pored air filter cover

Washable

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Adjustable grip width

Suitable for all hydraulic Braktec brake systems

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Adjustable grip width

Suitable for all hydraulic Braktec clutch mountings.

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Braktec brake system

• Coated neoprene ring
• Simply pulled over the grips
• Optimum protection against blisters on the thumbs with these coated neoprene rings