EC300 2021

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

• Highest quality workmanship
• Including straps

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Height: 43 cm

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Height: 43 cm

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

High stiffness and strength

Made of high-quality carbon

Optimal protection against stone impact

Visual highlight

Optimal protection against stone impact

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Fits all Braktec brake- and clutch reservoirs

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Adjustable grip width

Suitable for all hydraulic Braktec brake systems

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

Perfect for all on the move

Exceptionally robust

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

• Visual highlight
• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

Chain breaker

Patented gage for two important checks:

Check and adjust chain tension

Check chain lengthening (wear)

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Adjustable grip width

Suitable for all hydraulic Braktec clutch mountings.

Protects from damage in the event of a fall

Easy to mount

Protects the fork

Resistant to the toughest stresses and strains

Ideal protection for sealing the fork

Mounted directly on the fork

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

CNC milled from high-strength aluminium

Elegant anodized surface

Visual highlight

Perfect fit

Made of high-quality carbon

Optimal protection against stone impact

Only for Brembo systems

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached with a special bracket on the handlebar

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Perfect fit

Made of high-quality carbon

Optimal protection against stone impact

Only for Brembo systems

Made of high-strength aluminium

Elegant anodized surface

Pure race feeling

Provides more traction when starting

Mounted directly on the fork

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing ring

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

• Contents are in accordance with DIN standard 13167-2014 for motorcyclists
• Note: It is mandatory to carry a first aid kit in many countries (such as Austria, Italy, Portugal and Spain)