MC125 2021

Air filter box front part

Air filter box front section

• Protects the intake system against water and dirt when cleaning the air filter box

Perfect fit

Optimal basis for graphics kits

Perfect fit

Optimal basis for graphics kits

• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover

• Recommended for extremely dusty conditions

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

• Highest quality workmanship
• Including straps

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Height: 43 cm

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Height: 43 cm

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

• Developed together with the vehicle
• Specially developed for WP forks
• Fork bleeding using finger pressure

High stiffness and strength

Made of high-quality carbon

Optimal protection against stone impact

Visual highlight

Optimal protection against stone impact

• Made of high-strength aluminium
• Improved braking performance

• Made of high-strength aluminium
• Improved braking performance

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

• Outer ring made of stainless high-performance brake steel
• Larger diameter for added braking performance

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tire changes, brake service etc. without removing the brake cover

Manufactured using state-of-the-art 2-component injection moulding technology

CNC milled from high-strength aluminium

Lighter than series components

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Elegant anodized surface

Visual highlight

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Adjustable grip width

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

Perfect for all on the move

Exceptionally robust

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

• Visual highlight
• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability