MC250F 2021

Air filter box front part

Air filter box front section

• Protects the intake system against water and dirt when cleaning the air filter box

Perfect fit

Optimal basis for graphics kits

Perfect fit

Optimal basis for graphics kits

• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover

• Recommended for extremely dusty conditions

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

• Highest quality workmanship
• Including straps

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Height: 43 cm

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Height: 43 cm

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

• Developed together with the vehicle
• Specially developed for WP forks
• Fork bleeding using finger pressure

High stiffness and strength

Made of high-quality carbon

Optimal protection against stone impact

Visual highlight

Optimal protection against stone impact

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Softer due to high content of organic substances
• Thermal insulation by means of ceramic underlayer
• Less aggressive brake feel
• Lower friction coefficient than sintered brake pads
• Special material mixture

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

Perfect for all on the move

Exceptionally robust

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

• Visual highlight
• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

Chain breaker

Patented gage for two important checks:

Check and adjust chain tension

Check chain lengthening (wear)

• Made of high-strength aluminium

• Easy to mount
• Protects from damage in the event of a fall

• Easy to mount
• Protects from damage in the event of a fall

Protects from damage in the event of a fall

Easy to mount

Protects the fork

Resistant to the toughest stresses and strains

Ideal protection for sealing the fork

Mounted directly on the fork

• Anodized hub milled from a whole piece
• Maximum weight saving compared to standard wheels
• Maximum gain in handling and, at the same time, stability in challenging off-road situations
• Anodized aluminum spoke nipples