Technical Accessories

Resistant to the toughest stresses and strains

Forged lightening indents reduce rotational mass

Grooves between the teeth clear dirt under the chain

Extends chain life

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Fits all Braktec brake- and clutch reservoirs

Manufactured using state-of-the-art 2-component injection moulding technology

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tyre changes, brake service etc. without removing the brake cover

Noble material mix of carbon fibre and plastic

Up to 260mm brake disc

Elegant look

• Coated neoprene ring
• Simply pulled over the grips
• Optimum protection against blisters on the thumbs with these coated neoprene rings

• CNC milled from high-strength aluminium
• Elegant anodized surface
• Visual highlight

Wider contact surface than standard:

• + 8 mm for 125/150 SX/XC-W, SX-F, 450/500 EXC-F
• +16 mm for 250/300 SX/EXC, 250/350 EXC-F

• Exceptionally robust
• Extremely light

• Recommended for long journeys
• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

Elegant cover

Seat cover with transversely stitched ribs

Maximum grip with unrestricted freedom of movement

For standard height seats

Patented gage for two important checks

Check and adjust chain tension

Check chain lengthening (wear)

Perfect fit

No new engine flashing necessary

Resistant to the toughest stresses and strains

Substantial weight saving

Conversion kit from separate lubrication to premix especially made for hard enduro use

Provides optimum protection

For rear sprockets up to 53T and 220 mm - 270 mm brake discs

Fast and easy inductive charging of the smartphone during the ride

Can be mounted on the SPC+ smartphone bracket and smartphone adapter

Including USB-A charging cable

This mat is already mandatory for many races

The special material mix absorbs overflowing fuel

The mat also facilitates the retrieval of tools, screws and other small parts during service work

Complies with FIM regulations

Rubberised back

Size: 200cm x 100cm

Exceptionally robust

CNC milled from high-strength aluminium

Resistant to the toughest stresses and strains

Elegant anodised surface

Easy to mount

Maximum protection against falls, flying stones, branches, etc

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

The weight-optimised water pump cover ensures maximum water flow

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Air filter box cover

Ergonomically perfect shape (the result of years of racing experience)

Substantial weight saving

Weight-optimized shape compared to stock fuel tank (7l instead of 7.9l)

Allows more air flow through the radiators

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Braktec system

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Braktec system

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Braktec system

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Made of the highest quality materials

Tested in the toughest conditions

Developed together with the vehicle

Enables shorter drivers to also achieve the optimum seat height

Perfect compromise between maximum chassis performance and lowest possible vehicle height

No restrictions on riding dynamics

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Robust, solid construction

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Robust, solid construction

Floating

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

With Flame design for added braking performance

Custom designed seat for an uncompromising look

Resistant coating

Seat cover with transversely stitched ribs

Maximum grip with unrestricted freedom of movement

Same seat height like the standard seat

High-quality, adjustable torque wrench 5-25 NM, including the following accessories:-

Push-on spoke wrenches in sizes 5.65 and 6.95mm

Push-on ratchet ¼"

Ratchet attachments: 6, 8, 10mm socket wrench, 15 Torx

This mat is already mandatory for many races

The special material mix absorbs overflowing fuel

The mat also facilitates the retrieval of tools, screws and other small parts during service work

Complies with FIM regulations

Rubberised back

Size: 200 cm x 100 cm