Technical Accessories

Elegant cover

Resistant coating

Plenty of freedom of movement and yet perfect hold

The “Wave surface” has the effect of a gradation

Same seat height like the standard seat

For all 48 mm forks

Ideal protection for sealing the fork

For use with an open fork protector

Resistant to the toughest stresses and strains

Ideal protection for sealing the fork

Mounted directly on the fork

Permanent protection against unattractive scratches and matte spots on the swingarm

Protects from damage in the event of a fall

Anodised hub milled from a whole piece

Maximum weight saving compared to standard wheels

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Recommended in extremely wet conditions.

Acts as an additional protective layer

Washable

The steel piston ring, which is also installed in the WP Pro components shock absorbers, improves the service life of the piston and reduces the friction.

Which effects the response of the shock absorber positive.

Can be easily replaced when the shock absorber is serviced.

For piston diameter 50mm.

No fading

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Significantly longer lasting

With Flame design for added braking performance

Floating

Inner ring anodised

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

With exchangeable chain track surface, therefore extremely durable

Developed for use on the toughest off-road terrain

Developed according to the requirements of our factory drivers

Visual highlight

Race look

Streamlined profile with increased coverage of swing arm mounting tabs.

Large chamfered outside leading and bottom edges for maximum rock deflection.

Friction reducing additives and UV protection to eliminate colour fade. 

Resistant coating

Higher compared to the standard seat

+20mm

Protects from damage in the event of a fall

Easy to mount

Protects the fork

For all 48 mm forks

Ideal protection for sealing the fork

For use with an open fork protector

Know exactly when the next service is due

Including rev counter

High stiffness and strength

Made of high-quality carbon

Optimal protection against stone impact

Visual highlight

Optimal protection against stone impact

Makes setting the sag significantly simpler

Folding version for easy stowing in the tool box

Resistant to the toughest stresses and strains

Forged lightening indents reduce rotational mass

Grooves between the teeth clear dirt under the chain

Extends chain life

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Made of robust material

Pre-cut stickers

Universal and inconspicuous bracket for your smartphone

Optimal solution for quick and secure fastening of your smartphone on the vehicle

Can be clamped on the handlebar (including different adapter)

The arm can be rotated in any position for the perfect position for your smartphone

Includes also a anti vibration module which decouples the smartphone from the bracket / motorcycle with a specific developed elastomer inlay

It reduces the transfer of vibrations, generated by the motorcycle, to the smartphone and protects it`s sensitive components

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

Makes removal of the front wheel easier

For all front axles with a diameter of 22 mm

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Braktec brake system

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Braktec brake system

Specially developed for LiFePo4-batteriesVoltages 13.2 V

Charging current - 2.5 amps

Optimizes battery performance and service life

Recovery mode for low battery voltage

Precise battery monitoring

There's racing experience here as well!

Practical tyre lever set, consisting of

3 x short version 51012092100

3 x long version 51012093100

Convenient and easy to use

Made of the highest quality materials

The quick-lock coupling remains on the air fork

Ideal when using the quick lock kit with multiple motorcycles

This clever tool is a must for every motorcycle toolbox

With it, you can remove dirt from your fork seals effortlessly

No matter whether it's in the garage or directly at the racetrack this tool extends the life of your seals many times over

For all 48 mm forks

With scaling for both the fluid level and different mixture ratios

Perfect for changing the oil and for preparing larger quantities of 2-stroke mixture in the canister

Simple handling thanks to the ergonomic design

Perfect for all on the move

Exceptionally robust

Can be used with XACT/ XPLOR forks and shocks

Dimensions L=44,09 inch / W=16,14 inch / H=6,30 inch

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Height: 43 cm

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Robust, solid construction

Modern and simple design

Easy to mount

New bike stand generation

Plastic - aluminium combined for highest stiffness

Extremely stable due to a broad stand design

Height: 43 cm

Top plate in 2k injection moulding technology

Side plates for graphics mounting

Use either the supplied, or your own graphics

Maximum protection against falls, flying stones, branches, etc

Indispensable companion for heavy off-road and Supermoto use

Wide, generous design in combination with sturdy aluminium bracket

Prevents broken levers

Made of robust plastic

Made of robust plastic

Fastening independent of fittings directly on the handlebars

To convert the open, standard handguards to a closed version

Made of robust plastic

Fastening independent of fittings directly on the handlebars

To convert the open, standard handguards to a closed version