Technical Accessories

CNC milled aluminium triple clamp

Elegant anodised surface

Visual highlight

Optimally tuned steering stem stiffness

100% alignment of the fork tubes

Ideal flexibility – precisely customised to the WP fork

Specially optimised geometry of the fork clamping

No ovalization of the fork outer tube

Highly precise and smooth fork response

Maximum handling gain

Gain in stability at the front wheel

Overall, more homogeneous force flows in the entire vehicle

Simple offset adjustment

Including steering stem with steering head bearing already pressed on

Very simple offset adjustment of 20 or 22 mm

Shorter offset: Stability on fast straights

Longer offset: easier and quicker cornering in curves

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

CNC milled from high-strength aluminium

Best possible effective protection for the clutch slave cylinder

Prevents damage to the engine housing in the event of chain cracks

No stones drawn in between chain and engine housing (gentle on the material)

Protects from damage in the event of a fall

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Adjustable grip width

Suitable for all hydraulic Braktec clutch mountings.

Resistant coating

Enables shorter drivers to also achieve the optimum seat height

Lower compared to the standard seat

Permanent protection against unattractive scratches and matte spots on the swingarm

Protects from damage in the event of a fall

Protects the radiator from mud, dirt and sand

Protection against rapid overheating of the engine in muddy conditions

Pre-cut stickers

Suitable for front and rear wheel rim

For wheel size 18/21"; 19/21"

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Braktec brake system

This clever tool is a must for every motorcycle toolbox

With it, you can remove dirt from your fork seals effortlessly

No matter whether it's in the garage or directly at the racetrack this tool extends the life of your seals many times over

For all 48 mm forks

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Manufactured using state-of-the-art 2-component injection moulding technology

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tyre changes, brake service etc. without removing the brake cover

Noble material mix of carbon fibre and plastic

Up to 260mm brake disc

Stabilises the motorcycle during transport

Protects the fork shaft sealing rings and fork springs against damage due to tension belts being tightened too much

Is clamped between the bottom of the front fender and tyre

Elegant look

• Coated neoprene ring
• Simply pulled over the grips
• Optimum protection against blisters on the thumbs with these coated neoprene rings

Chain breaker

• Exceptionally robust
• Extremely light

• Recommended for long journeys
• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

Endurance-tested for the toughest off-road applications

Easy to mount

Custom design

Extremely light

Extremely durable

Highest quality workmanship

Most effective protection for frame and engine

CNC milled from high-strength aluminium

Additionally hard anodised against corrosion

Protects the exhaust flange from damage and breakage

Made from high grade titanium

Uncompromising race look

Permanently welded brackets

Complies with current FIM noise regulations

Substantial weight saving

To install the silencer, the stock mounting parts must be overtaken

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing ring

Better cooling

Maximum performance

Provides more air

Plug & Play mounting

For use on EX models, the auxiliary wiring harnesses 77711979000 and 77711979044 are required

Provides more air

Maximum performance

Digital control

Current temperature can be read at any time

Variable switch-on temperature between 65 °C and 95 °C

Switch-off temperature 1 °C below the selected switch-on temperature

Provides better cooling of the engine

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

Original fairing parts, without the standard decor

Optimal basis for creating a unique design

Perfect fit

Personalise the look of your motorcycle

Kit contains:

Fork protector kit

Fender

Headlight shroud

Spoiler set

Air filter cover

Air filter panel

Tail section

All parts packed in a box

Original fairing parts, without the standard decor

Optimal basis for creating a unique design

Perfect fit

Personalise the look of your motorcycle

Kit contains

Fork protector kit

Fender

Headlight shroud

Spoiler set

Air filter cover

Air filter panel

Tail section

All parts packed in a box