Technical Accessories

Race look

Visual highlight

With exchangeable chain track surface, therefore extremely durable

Specially designed for the challenges of off-road use

CNC machined out of teflon

Stabilises the motorcycle during transport

Protects the fork shaft sealing rings and fork springs against damage due to tension belts being tightened too much

Is clamped between the bottom of the front fender and tyre

Keeps water out of the silencer during cleaning

For inner-diameter of 22-42 mm

Perfect fit

Optimal basis for graphics kits

Air filter box front section

Lower section of the air filter

Perfect fit

Optimal basis for graphics kits

• Made of the highest quality materials
• Visual highlight
• Perfect fit
• Personalize the look of your motorcycle
• Race look
• Designed to completely change the original look of your motorcycle
• Glue the graphics kit directly onto the standard fairing parts
• Can be removed without leaving any residue

• CNC milled from high-strength aluminium
• Elegant anodized surface
• Visual highlight

Wider contact surface than standard:

• + 8 mm for 125/150 SX/XC-W, SX-F, 450/500 EXC-F
• +16 mm for 250/300 SX/EXC, 250/350 EXC-F

• Convenient and easy to use
• Easy handling and operation
• Comfortable unhooking of springs

Chain breaker

• Made of high-strength aluminium
• Essential under extreme off-road conditions
• Fastened to silencer support on the rear frame
• Makes it easier to stand your motorcycle up

• Lower compared to the standard seat
• Resistant coating
• Enables shorter drivers to also achieve the optimum seat height

• Easy to mount
• Optimal protection against stone impact
• Provides maximum protection at the lowest possible weight
• Including adapted radiator protection grills

• Exceptionally robust
• Extremely light

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

• Recommended for long journeys
• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Elegant anodized surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customized to the WP fork
• Specially optimized geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum handling gain
• Gain in stability at the front wheel
• Overall, more homogeneous force flows in the entire vehicle
• Simple offset adjustment
• Including steering stem with steering head bearing already pressed on
• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves
• For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

Teeth made of high-strength steel, for an extra long service life

Aluminium centre section, reduces unsprung masses

Permanently joined together with high-strength rivets

At least three times longer service life than other aluminium rear sprockets

50 % lighter than steel rear sprockets

Longer service life of the entire drivetrain kit

On this spoke wrench, the torque is preset at 6 Nm.

This prevents over-tightening of the spoke nipples.

Too much torque when tightening the spoke nipples is the most frequent cause of broken spokes.

Wrench size 6.8 mm.

Perfect fit

Made of high-quality carbon

Optimal protection against stone impact

Only for Brembo systems

Perfect fit

Made of high-quality carbon

Optimal protection against stone impact

Only for Brembo systems

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing ring

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Resistant to the toughest stresses and strains

Ideal protection for sealing the fork

Mounted directly on the fork

No fading

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Significantly longer lasting

With Flame design for added braking performance

Floating

Inner ring anodised

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Optimal basis for graphics kits

Perfect fit

Protects from damage in the event of a fall

Easy to mount

Protects the fork

For all 48 mm forks

Ideal protection for sealing the fork

For use with an open fork protector

Know exactly when the next service is due

Including rev counter

High stiffness and strength

Made of high-quality carbon

Optimal protection against stone impact

Visual highlight

Optimal protection against stone impact

Makes setting the sag significantly simpler

Folding version for easy stowing in the tool box