Technical Accessories

Anodised hub milled from a whole piece

Maximum gain in handling and, at the same time, stability in challenging off-road situations

Anodised aluminium spoke nipples

Reinforced spokes for higher impact resistance

Recommended for extremely dusty conditions

Acts as an additional protective layer

Extends the filter service intervals

Premature sanding of the air filter is avoided

CNC milled handlebar mount with damping rubber inserts

Gentle on wrists and shoulder joints

Damping of hard shocks

Absorption of chassis and engine vibrations

Additional handlebar damping in horizontal direction

Optimum steering precision

Handlebar height adjustable to 2 positions

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

A motorcycle hand grip can be mounted on the handle (not included)

The different guide plates allow a variation of the throttle valve opening.

Makes it easier to stand your motorcycle up

Made of high-strength aluminium

Essential under extreme off-road conditions

Fastened to silencer support on the rear frame

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Provides maximum protection at the lowest possible weight

Optimal protection against stone impact

Easy to mount

Fast preload adjustment

Use of the entire length of the thread on the shock absorber

Very easy operation

Extremely low weight

Dirt-resistance

Mechanical drive

Colour differences between the upper and lower triple clamp cannot be technically ruled out.

CNC milled aluminium triple clamp

Elegant anodised surface

Visual highlight

Optimally tuned steering stem stiffness

100% alignment of the fork tubes

Ideal flexibility – precisely customised to the WP fork

Specially optimised geometry of the fork clamping

No ovalization of the fork outer tube

Highly precise and smooth fork response

Maximum handling gain

Gain in stability at the front wheel

Overall, more homogeneous force flows in the entire vehicle

Simple offset adjustment

Including steering stem with steering head bearing already pressed on

Very simple offset adjustment of 20 or 22 mm

Shorter offset: Stability on fast straights

Longer offset: easier and quicker cornering in curves

High stiffness and strength

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

Visual highlight

Changes the handling of the motorcycle

Gain in stability therefore recommended for fast tracks

Plug & Play mounting

Attachment to handlebar

Highest quality workmanship

With exchangeable chain track surface, therefore extremely durable

Specially designed for the challenges of off-road use

High stiffness and strength

80 % lighter than steel with the same load-bearing capacity

Elegant look

Low thermal expansion

Made of high-quality carbon

High long-term temperature stability

Non-corrosive

Maximum protection against falls, flying stones, branches, etc.

Can only be fitted with a standard header

Extra strong sheet steel

Nickel-plated surface

Full sound

Better power delivery

Extra strong sheet steel

Untreated surface

Full sound

Better power delivery

Silencer housing made of high-grade titanium

Blue anodised outer sleeve

Rich sound

Low noise level

Easy to mount

Perfect fit

Extremely low weight

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

100 mm length

20 blades: 0,05 - 0,1 - 0,15 - 0,2 - 0,25 - 0,3- 0,35 - 0,4 - 0,45 - 0,5 - 0,55 - 0,6 - 0,65 - 0,7 - 0,75 - 0,8 - 0,85 - 0,9 - 0,95 - 1,0 mm

Elegant cover

Seat cover with transversely stitched ribs

Maximum grip with unrestricted freedom of movement

For standard height seats

Elegant cover

Resistant coating

Plenty of freedom of movement and yet perfect hold

The “Wave surface” has the effect of a gradation

Same seat height like the standard seat

For all 48 mm forks

Ideal protection for sealing the fork

For use with an open fork protector

Resistant to the toughest stresses and strains

Ideal protection for sealing the fork

Mounted directly on the fork

Recommended in extremely wet conditions.

Acts as an additional protective layer

Washable

The steel piston ring, which is also installed in the WP Pro components shock absorbers, improves the service life of the piston and reduces the friction.

Which effects the response of the shock absorber positive.

Can be easily replaced when the shock absorber is serviced.

For piston diameter 50mm.

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

No fading

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Significantly longer lasting

With Flame design for added braking performance

Floating

Inner ring anodised

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

With exchangeable chain track surface, therefore extremely durable

Developed for use on the toughest off-road terrain

Developed according to the requirements of our factory drivers

Visual highlight

Race look

Streamlined profile with increased coverage of swing arm mounting tabs.

Large chamfered outside leading and bottom edges for maximum rock deflection.

Friction reducing additives and UV protection to eliminate colour fade. 

Protects from damage in the event of a fall

Easy to mount

Protects the fork

For all 48 mm forks

Ideal protection for sealing the fork

For use with an open fork protector

Know exactly when the next service is due

Including rev counter