Technical Accessories

• Exceptionally robust
• Extremely light

These CNC-machined, high-strength aluminum handlebar risers are extremely robust thanks to their special screw fastening (from below) on the triple clamp

Twisting and bending are therefore practically impossible

Use of these handlebar risers is only possible on CNC-machined triple clamps

Available in three different heights

• Recommended for long journeys
• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

• Elegant anodized surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customized to the WP fork
• Specially optimized geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum handling gain
• Gain in stability at the front wheel
• Overall, more homogeneous force flows in the entire vehicle
• Simple offset adjustment
• Including steering stem with steering head bearing already pressed on
• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves
• For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

Easily accessible and within the rider's field of vision

Fast and easy inductive charging of the smartphone during the ride

Can be mounted on the SPC+ smartphone bracket and smartphone adapter

Including USB-C charging cable

Teeth made of high-strength steel, for an extra long service life

Aluminium centre section, reduces unsprung masses

Permanently joined together with high-strength rivets

At least three times longer service life than other aluminium rear sprockets

50 % lighter than steel rear sprockets

Longer service life of the entire drivetrain kit

On this spoke wrench, the torque is preset at 6 Nm.

This prevents over-tightening of the spoke nipples.

Too much torque when tightening the spoke nipples is the most frequent cause of broken spokes.

Wrench size 6.8 mm.

Perfect fit

Made of high-quality carbon

Optimal protection against stone impact

Only for Brembo systems

Perfect fit

Made of high-quality carbon

Optimal protection against stone impact

Only for Brembo systems

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Incl. special low friction shaft sealing ring

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

Resistant to the toughest stresses and strains

Ideal protection for sealing the fork

Mounted directly on the fork

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Floating

Inner ring anodised

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Optimal basis for graphics kits

Perfect fit

Optimal basis for graphics kits

Perfect fit

Protects from damage in the event of a fall

Easy to mount

Protects the fork

For all 48 mm forks

Ideal protection for sealing the fork

For use with an open fork protector

Know exactly when the next service is due

Including rev counter

High stiffness and strength

Made of high-quality carbon

Optimal protection against stone impact

Visual highlight

Optimal protection against stone impact

Makes setting the sag significantly simpler

Folding version for easy stowing in the tool box

Resistant to the toughest stresses and strains

Forged lightening indents reduce rotational mass

Grooves between the teeth clear dirt under the chain

Extends chain life

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Made of robust material

Pre-cut stickers

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

Wheel bearing repair kit with wheel bearing protection cap set and low friction shaft sealing rings

LED technology, specially developed for use with the Enduro

Very high light output

Light intensity 1500 lm

Light colour approx. 5,500 K

Exceptionally robust

Comes with white headlight mask for plug & play mounting

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Braktec brake system

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Braktec brake system

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

High stiffness and strength

Extremely light

Extremely durable

Low thermal expansion

High long-term temperature stability

Maximum protection against falls, flying stones, branches, etc

Visual highlight

Protects against heat and unwanted contact

Can only be fitted to headers without a soundbox