Technical Accessories

• Stabilizes the motorcycle during transport
• After transport, the tool serves as a perfect plug-in stand!

• Plug-in stand and fork support in one part
• Two tools in one
• Saves space when transporting your motorcycle
• Stabilizes the motorcycle during transport
• Protects the fork shaft sealing rings and fork springs against damage due to tension belts being tightened too much
• After transport, the tool serves as a perfect plug-in stand!

• Made of high-strength aluminium
• Essential under extreme off-road conditions
• Fastened to silencer support on the rear frame
• Makes it easier to stand your motorcycle up

Air filter box front part

• For all 48 mm forks
• Extra strong film

• For all 48 mm forks
• Extra strong film

• Developed according to the requirements of our factory drivers
• Allows tighter fuel hose routing along the engine
• Prevents unintentional disconnection of the fuel hose in off-road applications

• Particularly safe due to clever design
• Clutch is secured by simply twisting the connection

Recommended for storing your timecard during races

Stick it directly to the seat with grip glue

• Lower compared to the standard seat
• Resistant coating
• Enables shorter drivers to also achieve the optimum seat height

• For extremely muddy conditions
• Protects the radiator from mud, dirt and sand
• Protection against rapid overheating of the engine in muddy conditions

• Reduces dirt deposits between engine and skid plate
• Provides better cooling of the engine

• Easy to mount
• Protects from damage in the event of a fall

• Easy to mount
• Optimal protection against stone impact
• Suitable for the left and right side
• Provides maximum protection at the lowest possible weight

• Easy to mount
• Protects from damage in the event of a fall

• Prevents abrasion of the frame by dirt, falls or the driver's boots
• Protects trousers and boots from burns on the exhaust side

Medium strength thread lock - contents, 50 ml

• Temperature resistant from -55 to +200 °C
• Fills gaps up to 0.25 mm
• Final strength achieved after 1 to 3 hours

The repair kit is a two-component epoxy resin adhesive. Hardens at room temperature: accelerated hardening possible by raising the temperature

Use: Particularly suitable for steel, but also other metals, wood, concrete, ceramics, glass and most plastics. The steel bond is resistant to, among other things, oil, gasoline, diesel and battery acid

Processing: Best results are achieved with clean and rough surfaces. Cut off the required amount and knead for approx. 1 minute until a uniform color is achieved. Use within 2 minutes

At first, it seems as if there is no adhesion. Just carry on and press the adhesive mixture into the surface. Remove any excess material. When coating or repairing surfaces that are still wet, leak or are under water, apply pressure until adhesion begins. Smooth flat with water by hand for an even surface. Wash your hands with soap and water (or with a Turbo cleaning towelette) immediately after completing your work. Hardening commences after 5 to 10 minutes

The repaired part can be used again after as little as 60 minutes. The surfaces to be glued must be dry and free from dust and grease

Contents: 56 g

• 3.5 x 16.5"
• Black matte
• Comes with bushings for 26mm axle diameter
• Can be adapted to other axle diameter by using the bike's stock bushings

• 5 x 17"
• Black matte
• Comes with bushings for 20mm axle diameter
• Can be adapted to other axle diameter by using the bike's stock bushings

• Anodized hub milled from a whole piece
• Maximum weight saving compared to standard wheels
• Maximum gain in handling and, at the same time, stability in challenging off-road situations
• Anodized aluminum spoke nipples

• Universally applicable for mounting the GPS bracket

• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover

• Recommended for extremely dusty conditions

• Developed according to the requirements of our factory drivers
• Gain in stability at the front wheel
• High-end steering damper
• Maximum control on fast tracks
• Fully adjustable
• Well thought-out mounting of the damper enables individual handlebar adjustment
• Reduced weight
• Sensitive response behavior
• High speed DCC
• Optimum 25 click setting range.
• Proven success with the KTM Works Rally Team.

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent (A54007930000FA) is required

Steering damper bracket

Steering damper counter bearing

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily