Technical Accessories

• 5 x 17"
• Black matte
• Comes with bushings for 20mm axle diameter
• Can be adapted to other axle diameter by using the bike's stock bushings

• Anodized hub milled from a whole piece
• Maximum weight saving compared to standard wheels
• Maximum gain in handling and, at the same time, stability in challenging off-road situations
• Anodized aluminum spoke nipples

• Universally applicable for mounting the GPS bracket

• Tested in the toughest conditions
• Installed in the standard clutch, which means simple, uncomplicated and fast installation
• Unlimited and total concentration on the perfect line
• New generation of Rekluse centrifugal clutch with EXP technology
• Easily adjustable from the outside via the clutch slave cylinder
• No stalling of the engine in critical situations, such as braking, downhill runs, jumping, or when starting or pushing
• Improved traction, controllable by the throttle alone
• Slippery, extremely steep sections can be managed more easily > saves time and ensures faster lap times
• More relaxed, fatigue-free and controlled riding, even over longer distances and in tough terrain
• No more coupling is required, although it is still possible
• Special rear brake conversion kit available, allowing braking of the rear wheel with the left hand

• CNC milled from high-strength aluminium
• Improves heat dissipation
• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components

• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover

• Recommended for extremely dusty conditions

• Developed according to the requirements of our factory drivers
• Gain in stability at the front wheel
• High-end steering damper
• Maximum control on fast tracks
• Fully adjustable
• Well thought-out mounting of the damper enables individual handlebar adjustment
• Reduced weight
• Sensitive response behavior
• High speed DCC
• Optimum 25 click setting range.
• Proven success with the KTM Works Rally Team.

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent (A54007930000FA) is required

Steering damper bracket

Steering damper counter bearing

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Including all required assembly materials
• Extremely sturdy aluminium brackets
• Prevents broken levers

• Made of sturdy plastic
• Converts the originally open handguards into a closed version
• Mounting independent to the lever mounting, directly to the handlebar
• Compatible also with handguards 79602979000EB/28/30/AB and 72102979000EB/28/30

• To make the mounting of the wrap-around handguard kit 79702984044 resp. of the Handguard kits 7970297900030 / 28 / AB / EB easier
• Increases the space between alu-guard and hand brake cylinder

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Warm hands, no matter what the weather

• A motorcycle hand grip can be mounted on the handle (not included)

• Right grip permanently glued to the throttle grip
• Left grip with aluminium clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• For extremely muddy conditions
• Protects the radiator from mud, dirt and sand
• Protection against rapid overheating of the engine in muddy conditions

• Provides better cooling of the engine
• Provides more air
• Maximum performance
• Digital control
• Current temperature can be read at any time
• Variable switch-on temperature between 65 °C and 95 °C
• Switch-off temperature 1 °C below the selected switch-on temperature

• Special factory radiators
• More efficient cooling due to larger surface area
• Including special radiator hoses and radiator protections

• Prevents the chain from hitting the rear tyre
• Perfect chain guide, no branches drawn in between chain and engine housing

• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Visual highlight
• Specially developed for use in motocross
• No O- or Z-rings > minimum loss of power and good durability

• Greater flexibility and better running characteristics
• Constant and permanent lubrication
• Better sealing against water and dirt
• Significantly longer durability

• For all 48 mm forks
• Made of high-quality carbon