Technical Accessories

Resistant coating

Enables shorter drivers to also achieve the optimum seat height

Lower compared to the standard seat

Permanent protection against unattractive scratches and matte spots on the swingarm

Protects from damage in the event of a fall

Protects the radiator from mud, dirt and sand

Protection against rapid overheating of the engine in muddy conditions

Pre-cut stickers

Suitable for front and rear wheel rim

For wheel size 18/21"; 19/21"

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Braktec brake system

This clever tool is a must for every motorcycle toolbox

With it, you can remove dirt from your fork seals effortlessly

No matter whether it's in the garage or directly at the racetrack this tool extends the life of your seals many times over

For all 48 mm forks

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Mounting not possible with Twinwall handlebars

Attached directly at the levers with a special mounting

Only mountable with Brembo brake system

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Manufactured using state-of-the-art 2-component injection moulding technology

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tyre changes, brake service etc. without removing the brake cover

Noble material mix of carbon fibre and plastic

Up to 260mm brake disc

Stabilises the motorcycle during transport

Protects the fork shaft sealing rings and fork springs against damage due to tension belts being tightened too much

Is clamped between the bottom of the front fender and tyre

Elegant look

• Coated neoprene ring
• Simply pulled over the grips
• Optimum protection against blisters on the thumbs with these coated neoprene rings

• Recommended for long journeys
• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

Made from high grade titanium

Uncompromising race look

Permanently welded brackets

Complies with current FIM noise regulations

Significantly more performance

Substantial weight saving

To install the silencer, the stock mounting parts must be overtaken

Endurance-tested for the toughest off-road applications

Easy to mount

Extremely light

Extremely durable

Highest quality workmanship

Noble material mix of carbon fibre and plastic

Most effective protection for frame and engine

Manufactured using state-of-the-art 2-component injection moulding technology

On this spoke wrench, the torque is preset at 6 Nm.

This prevents over-tightening of the spoke nipples.

Too much torque when tightening the spoke nipples is the most frequent cause of broken spokes.

Wrench size 6.8 mm.

Resistant coating

Seat cover with transversely stitched ribs

Maximum grip with unrestricted freedom of movement

Same seat height like the standard seat

Custom designed seat for an uncompromising look

Protects the intake system against water and dirt when cleaning the air filter box

To prevent the ingress of water in the silencer when cleaning

Kit contains all required covers for a thoroughly cleaning process of the bike:

Air filter cover

Plug

Wash cap set

Weight-optimised

Visual highlight with technical and ergonomic added value

Maximum handling gain

Changes the handling of the motorcycle

Gain in handling therefore recommended for tighter tracks

Protects the brake disc in the event of a fall

High stiffness and strength

Protects the rear brake disc from stones and other solid obstacles

CNC milled from high-strength aluminium

Lighter than series components

Improved braking performance

Plug-in stand and fork support in one part

Two tools in one

Saves space when transporting your motorcycle

Stabilises the motorcycle during transport

Protects the fork shaft sealing rings and fork springs against damage due to tension belts being tightened too much

After transport, the tool serves as a perfect plug-in stand!