Technical Accessories

Use this to remove the dirt from your last mud battle with ease!

A motorcycle grip rubber (not included) can be fitted to the grip

CNC milled from high-strength aluminium

Elegant anodized surface

Visual highlight

• Anodized valve caps
• With valve opener function

These CNC-machined, high-strength aluminum handlebar risers are extremely robust thanks to their special screw fastening (from below) on the triple clamp

Twisting and bending are therefore practically impossible

Use of these handlebar risers is only possible on CNC-machined triple clamps

Available in three different heights

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Elegant look

• Coated neoprene ring
• Simply pulled over the grips
• Optimum protection against blisters on the thumbs with these coated neoprene rings

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

Protects the intake system against water and dirt when cleaning the air filter box

Perfect fit

Resistant coating

Higher compared to the standard seat

Perfect fit

Resistant coating

Enables shorter drivers to also achieve the optimum seat height

Lower compared to the standard seat

Custom designed seat for an uncompromising look

Resistant coating

Seat cover with transversely stitched ribs

Maximum grip with unrestricted freedom of movement

Same seat height like the standard seat

Endurance-tested for the toughest off-road applications

Easy to mount

Extremely durable

Made of high-strength aluminium

Highest quality workmanship

Custom design

Most effective protection for frame and engine

Extremely resistant fastening system

CNC milled from high-strength aluminium

Resistant to the toughest stresses and strains

Weight-optimised

105 Factory kit with more displacement (105 instead of 85)

Significantly more torque

Significantly more performance

100% alignment of the fork tubes

CNC milled aluminium triple clamp

Elegant anodised surface

Highly precise and smooth fork response

Including steering stem with steering head bearing already pressed on

Overall, more homogeneous force flows in the entire vehicle

No ovalization of the fork outer tube

Maximum handling gain

Optimally tuned steering stem stiffness

Visual highlight

Ideal flexibility – precisely customised to the WP fork

Specially optimised geometry of the fork clamping

Gain in stability at the front wheel

Extra strong sheet steel

Nickel-plated surface

Wide, even engine speed range

Better gas control

Combination with FMF silencer recommended

Silencer housing made of high-grade aluminium

Stainless steel silencer cap

Rich sound

Permanently welded brackets

Easy to mount

Reduced weight

For a system with optimized performance and perfect balance we recommend the combination with the FMF Fatty expansion chamber

FMF FACTORY FATTY EXPANSION CHAMBER

Provides optimum protection

For rear sprockets up to 53T and 220 mm - 270 mm brake discs

This mat is already mandatory for many races

The special material mix absorbs overflowing fuel

The mat also facilitates the retrieval of tools, screws and other small parts during service work

Complies with FIM regulations

Rubberised back

Size: 200cm x 100cm

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

High-quality, adjustable torque wrench 5-25 NM, including the following accessories:-

Push-on spoke wrenches in sizes 5.65 and 6.95mm

Push-on ratchet ¼"

Ratchet attachments: 6, 8, 10mm socket wrench, 15 Torx

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Colored top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting

Secure stand for your bike

Made especially for 50 / 65 / 85 models

Aluminium construction with a non-slip pad.

The top is wedge shaped and solid so the bike doesn't slide around when washing.

Testing, charging and keeping batteries fresh

Fully automatic and economical battery charging by means of programmed charge characteristic

Short-circuit protection

Reverse polarity protection

Can be used for several types of batteries (Pb, LiFePo4)

Charging with constant power, or with a specific power control program

Trickle charge during diagnostic or flashing the vehicle

Recovery mode for low battery voltage (BMS, battery management system)

Optimizes battery performance and service life

Precise battery monitoring

Including power supply cable type UK

100 mm length

20 blades: 0,05 - 0,1 - 0,15 - 0,2 - 0,25 - 0,3- 0,35 - 0,4 - 0,45 - 0,5 - 0,55 - 0,6 - 0,65 - 0,7 - 0,75 - 0,8 - 0,85 - 0,9 - 0,95 - 1,0 mm

No fading

Outer ring made of stainless high-performance brake steel

Minimal wear on brake pads

Significantly longer lasting

With Flame design for added braking performance

Know exactly when the next service is due

Including rev counter

Lightweight material

Open design

Fastening directly on the handlebar or with a special support directly on the fittings

Makes setting the sag significantly simpler

Folding version for easy stowing in the tool box

Made of robust material

Pre-cut stickers

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting.