Technical Accessories

Resistant coating

Enables shorter drivers to also achieve the optimum seat height

Lower compared to the standard seat

Permanent protection against unattractive scratches and matte spots on the swingarm

Protects from damage in the event of a fall

Protects the radiator from mud, dirt and sand

Protection against rapid overheating of the engine in muddy conditions

Pre-cut stickers

Suitable for front and rear wheel rim

For wheel size 18/21"; 19/21"

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Fits all Braktec brake- and clutch reservoirs

Uncompromising race look

Extremely light

Open design 2-component plastic handguard

Black middle section = maximum strength for optimum protection

Coloured top and bottom parts = highly flexible under the roughest conditions

Attached with a special bracket on the handlebar

Manufactured using state-of-the-art 2-component injection moulding technology

Extremely light

Protects the brake disc from stones and other solid obstacles

Central adapter replaces the spacer sleeve on the wheel axle

Allows tyre changes, brake service etc. without removing the brake cover

Noble material mix of carbon fibre and plastic

Up to 260mm brake disc

CNC milled from high-strength aluminium

Elegant anodized surface

Visual highlight

Elegant look

• Coated neoprene ring
• Simply pulled over the grips
• Optimum protection against blisters on the thumbs with these coated neoprene rings

• CNC milled from high-strength aluminium
• Elegant anodized surface
• Visual highlight

Wider contact surface than standard:

• + 8 mm for 125/150 SX/XC-W, SX-F, 450/500 EXC-F
• +16 mm for 250/300 SX/EXC, 250/350 EXC-F

• Exceptionally robust
• Extremely light

• Recommended for long journeys
• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear

• Significantly longer lasting
• Very high friction coefficient for maximum and permanent braking force
• Very good braking effect even in wet conditions
• For extreme operating conditions (sand, gravel...)
• Eliminates “fading” almost completely

Extra strong sheet steel

Nickel-plated surface

Full sound

Better power delivery

Combination with FMF silencer recommended

Specially developed for use in motocross

Silencer housing made of high-grade aluminium

Rich sound

Low noise level

Easy to mount

Perfect fit

Reduced weight

Suitable for standard silencers

Untreated surface

Uncompromising race look

Sensitive response

Increased performance

Improved throttle response and increases in both power and torque

Substantial weight saving

Saving almost 20% weight compared to the stock expansion chamber (ca. 0,4 kg)

Silencer housing made of high-grade titanium

Uncompromising race look

Sensitive response

Increased performance

Improved throttle response and increases in both power and torque

Substantial weight saving

Saving almost 20% weight compared to the stock expansion chamber (ca. 0,4 kg)

To install the silencer, the stock mounting parts must be overtaken

This mat is already mandatory for many races

The special material mix absorbs overflowing fuel

The mat also facilitates the retrieval of tools, screws and other small parts during service work

Complies with FIM regulations

Rubberised back

Size: 200cm x 100cm

Exceptionally robust

CNC milled from high-strength aluminium

Resistant to the toughest stresses and strains

Elegant anodised surface

Easy to mount

Maximum protection against falls, flying stones, branches, etc

Optimal protection against penetration of mud, sand and water into the wheel bearing of your wheel

Reduces wear on sealing rings and wheel bearings for longer service life

The weight-optimised water pump cover ensures maximum water flow

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Air filter box cover

Ergonomically perfect shape (the result of years of racing experience)

Substantial weight saving

Weight-optimized shape compared to stock fuel tank (7l instead of 7.9l)

Allows more air flow through the radiators

Installed in the standard clutch, which means simple, uncomplicated and fast installation

Unlimited and total concentration on the perfect line

New generation of Rekluse centrifugal clutch with EXP technology

Easily adjustable from the outside via the clutch slave cylinder

No stalling of the engine in critical situations, such as braking, downhill runs, jumping, or when starting or pushing

Improved traction, controllable by the throttle alone

Slippery, extremely steep sections can be managed more easily > saves time and ensures faster lap times

More relaxed, fatigue-free and controlled riding, even over longer distances and in tough terrain

No more coupling is required, although it is still possible

Special rear brake conversion kit available, allowing braking of the rear wheel with the left hand

Tested in the toughest conditions

New generation of Rekluse centrifugal clutch with EXP 4.0 technology

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Braktec system

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Braktec system

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Braktec system

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Made of the highest quality materials

Tested in the toughest conditions

Developed together with the vehicle

Enables shorter drivers to also achieve the optimum seat height

Perfect compromise between maximum chassis performance and lowest possible vehicle height

No restrictions on riding dynamics

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Robust, solid construction

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight

Robust, solid construction