Technical Accessories

• Easy to mount
• Protects from damage in the event of a fall

• Easy to mount
• Optimal protection against stone impact
• Suitable for the left and right side
• Provides maximum protection at the lowest possible weight

• Easy to mount
• Protects from damage in the event of a fall

• Prevents abrasion of the frame by dirt, falls or the driver's boots
• Protects trousers and boots from burns on the exhaust side

Medium strength thread lock - contents, 50 ml

• Temperature resistant from -55 to +200 °C
• Fills gaps up to 0.25 mm
• Final strength achieved after 1 to 3 hours

Perfect hold for your grips

Contents: 20g

The repair kit is a two-component epoxy resin adhesive. Hardens at room temperature: accelerated hardening possible by raising the temperature

Use: Particularly suitable for steel, but also other metals, wood, concrete, ceramics, glass and most plastics. The steel bond is resistant to, among other things, oil, gasoline, diesel and battery acid

Processing: Best results are achieved with clean and rough surfaces. Cut off the required amount and knead for approx. 1 minute until a uniform color is achieved. Use within 2 minutes

At first, it seems as if there is no adhesion. Just carry on and press the adhesive mixture into the surface. Remove any excess material. When coating or repairing surfaces that are still wet, leak or are under water, apply pressure until adhesion begins. Smooth flat with water by hand for an even surface. Wash your hands with soap and water (or with a Turbo cleaning towelette) immediately after completing your work. Hardening commences after 5 to 10 minutes

The repaired part can be used again after as little as 60 minutes. The surfaces to be glued must be dry and free from dust and grease

Contents: 56 g

Medium-strength thread lock

Suitable for all metal thread connections

• 3.5 x 16.5"
• Black matte
• Comes with bushings for 26mm axle diameter
• Can be adapted to other axle diameter by using the bike's stock bushings

• 5 x 17"
• Black matte
• Comes with bushings for 20mm axle diameter
• Can be adapted to other axle diameter by using the bike's stock bushings

• Anodized hub milled from a whole piece
• Maximum weight saving compared to standard wheels
• Maximum gain in handling and, at the same time, stability in challenging off-road situations
• Anodized aluminum spoke nipples

• Universally applicable for mounting the GPS bracket

• Tested in the toughest conditions
• Installed in the standard clutch, which means simple, uncomplicated and fast installation
• Unlimited and total concentration on the perfect line
• New generation of Rekluse centrifugal clutch with EXP technology
• Easily adjustable from the outside via the clutch slave cylinder
• No stalling of the engine in critical situations, such as braking, downhill runs, jumping, or when starting or pushing
• Improved traction, controllable by the throttle alone
• Slippery, extremely steep sections can be managed more easily > saves time and ensures faster lap times
• More relaxed, fatigue-free and controlled riding, even over longer distances and in tough terrain
• No more coupling is required, although it is still possible
• Special rear brake conversion kit available, allowing braking of the rear wheel with the left hand

• CNC milled from high-strength aluminium
• Improves heat dissipation
• Improves clutch performance and durability
• Hinson-typical surface treatment for significantly improved robustness compared to the standard part
• Very clean running of the clutch, which leads to reduced heat development when the clutch is pulled
• Can be installed in the standard clutch or in combination with other Hinson clutch components

• Acts as an additional protective layer
• Recommended for extremely dusty conditions
• Premature sanding of the air filter is avoided
• Coarse-pored air filter cover

• Recommended for extremely dusty conditions

• Developed according to the requirements of our factory drivers
• Gain in stability at the front wheel
• High-end steering damper
• Maximum control on fast tracks
• Fully adjustable
• Well thought-out mounting of the damper enables individual handlebar adjustment
• Reduced weight
• Sensitive response behavior
• High speed DCC
• Optimum 25 click setting range.
• Proven success with the KTM Works Rally Team.

For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent (A54007930000FA) is required

Steering damper bracket

Steering damper counter bearing

• CNC milled handlebar mount with damping rubber inserts
• Gentle on wrists and shoulder joints
• Damping of hard shocks
• Absorption of chassis and engine vibrations
• Additional handlebar damping in horizontal direction
• Optimum steering precision
• Further dampers available in three different degrees of hardness (soft, medium, hard) for individual adjustment

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

The connected power consumer can be switched off with the integrated switch

This prevents the battery from being drained unnecessarily

• Enables power consumers such as grip heater or radiator fans to be installed on SX or XC as well

• Excellent weather protection
• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Improved optics

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Including all required assembly materials
• Extremely sturdy aluminium brackets
• Prevents broken levers

• Made of sturdy plastic
• Converts the originally open handguards into a closed version
• Mounting independent to the lever mounting, directly to the handlebar
• Compatible also with handguards 79602979000EB/28/30/AB and 72102979000EB/28/30

• To make the mounting of the wrap-around handguard kit 79702984044 resp. of the Handguard kits 7970297900030 / 28 / AB / EB easier
• Increases the space between alu-guard and hand brake cylinder

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Closed design
• 2-component plastic handguard
• Black middle section = maximum strength for optimum protection
• Coloured top and bottom parts = highly flexible under the roughest conditions
• Available in two different heights
• Improved optics

• Warm hands, no matter what the weather