Technical Accessories

Stabilises the motorcycle during transport

Protects the fork shaft sealing rings and fork springs against damage due to tension belts being tightened too much

Is clamped between the bottom of the front fender and tyre

Perfect fit

Optimal basis for graphics kits

Elegant look

• Easy to mount
• Developed for use on the toughest off-road terrain
• Maximum protection at the lowest possible weight
• Custom design
• Manufactured using state-of-the-art 2-component injection molding technology
• Made from special, high-strength plastic
• Decoupled from the frame by rubber pads
• Mounting directly on the frame

Air filter box

• CNC milled from high-strength aluminium
• Elegant anodized surface
• Visual highlight

Wider contact surface than standard:

• + 8 mm for 125/150 SX/XC-W, SX-F, 450/500 EXC-F
• +16 mm for 250/300 SX/EXC, 250/350 EXC-F

• Easy to mount
• Optimal protection against stone impact
• Provides maximum protection at the lowest possible weight
• Including adapted radiator protection grills

Recommended in extremely wet conditions

• Exceptionally robust
• Extremely light

Available in five different heights

Included in the kit are 2x handlebar support lower parts and 2x fastening bolts

The upper parts and bolts required for clamping the handlebar are taken from the original handlebar support

The Y-distributor allows you to connect two power consumers to auxiliary wiring harness 77711979000

• Right grip permanently glued to the throttle grip
• Left grip with aluminium clamping ring for fixing on the handlebar
• Inconvenient gluing and securing with wire no longer necessary

• Recommended for long journeys
• Significantly longer durability
• Teeth made of high-strength steel, for an extra long service life
• Extremely low-wear

• Elegant anodized surface
• Visual highlight
• CNC milled aluminum triple clamp
• Optimally tuned steering stem stiffness
• 100% alignment of the fork tubes
• Ideal flexibility – precisely customized to the WP fork
• Specially optimized geometry of the fork clamping
• No ovalization of the fork outer tube
• Highly precise and smooth fork response
• Maximum handling gain
• Gain in stability at the front wheel
• Overall, more homogeneous force flows in the entire vehicle
• Simple offset adjustment
• Including steering stem with steering head bearing already pressed on
• Very simple offset adjustment of 20 or 22 mm
• Shorter offset: Stability on fast straights
• Longer offset: easier and quicker cornering in curves
• For use on Enduro MY21 and later (EU Version), the Factory fuel tank cap vent is required

Custom designed seat for an uncompromising look

Resistant coating

Seat cover with transversely stitched ribs

Maximum grip with unrestricted freedom of movement

Same seat height like the standard seat

Protects the intake system against water and dirt when cleaning the air filter box

Air filter box cover

Ergonomically perfect shape (the result of years of racing experience)

Substantial weight saving

Weight-optimized shape compared to stock fuel tank (7l instead of 7.9l)

Allows more air flow through the radiators

Uncompromising race look

Extremely light

Open design

Attached directly at the levers with a special mounting

Only mountable with Braktec system

Right grip permanently glued to the throttle grip

Left grip with aluminium clamping ring for fixing on the handlebar

Inconvenient gluing and securing with wire no longer necessary

The different guide plates allow a variation of the throttle valve opening

Optimal basis for creating a unique design

Easy to mount

Perfect fit

Personalise the look of your motorcycle

Pre-cut stickers

Suitable for front and rear wheel rim

High stiffness and strength

Protects against heat and unwanted contact

Extremely light

Extremely durable

Low thermal expansion

High long-term temperature stability

Maximum protection against falls, flying stones, branches, etc

Visual highlight

Endurance-tested for the toughest off-road applications

Easy to mount

Custom design

Extremely light

Extremely durable

Highest quality workmanship

Most effective protection for frame and engine

Increased tightening torque

Increased performance

More usable speed range

Better power delivery

Improved handling overall due to finer dosing capacity on the throttle grip

Sensitive response

Rich sound

Manifold routing optimally adapted to the production engine

Stainless steel header

Silencer housing made of high-grade titanium

Complies with current FIM noise regulations

Complies with current AMA noise regulations

To install the silencer, the stock mounting parts must be overtaken.

Uncompromising race look

Extremely light

Open design

TAIL SECTION

Uncompromising race look

Extremely light

Open design

2-component plastic handguard

Black middle section = maximum strength for optimum protection

Colored top and bottom parts = highly flexible under the roughest conditions

Attached directly at the levers with a special mounting

Protects the intake system against water and dirt when cleaning the air filter box

To prevent the ingress of water in the silencer when cleaning

Kit contains all required covers for a thoroughly cleaning process of the bike:

Air filter cover

Plug

Wash cap set

HEADLIGHT MASK REAR WALL

TAIL SECTION

Weight-optimised

Visual highlight with technical and ergonomic added value

Maximum handling gain

Changes the handling of the motorcycle

Gain in handling therefore recommended for tighter tracks

CNC milled from high-strength aluminium

Elegant anodised surface

Visual highlight with technical and ergonomic added value

Adjustable grip width

Suitable for all hydraulic Braktec brake systems

Better cooling

Maximum performance

Provides more air

Plug & Play mounting

For use on EX models, the auxiliary wiring harnesses 77711979000 and 77711979044 are required

Original fairing parts, without the standard decor

Optimal basis for creating a unique design

Perfect fit

Personalise the look of your motorcycle

Kit contains:

Fork protector kit

Fender

Headlight shroud

Spoiler set

Air filter cover

Air filter panel

Tail section

All parts packed in a box